SKS Instruction manual
Special thanks to Michael Hogan ([email protected]).
IMPORTANT: WARNINGS AND DISCLAIMERS
WARNING:
Careless use of any firearm can be dangerous. The warnings
and instructions in this manual should be read thoroughly
and understood before handling the SKS rifle. This is important
so that you might fully understand how to properly use your
SKS rifle. Accidential discharge can occur from careless
handling and could cause serious injury, death or damage to
property.
SKS RIFLES SHOULD BE CLEANED THOROUGHLY PRIOR TO USE.
DANGER- AMMUNITION WARNING:
Use only 7.62x39mm Soviet ammunition in your SKS rifle. Never
attempt to use ammunition of any other calibur in your gun.
Use only new manufactured ammunition that is of high quality
and in good condition. Never use remanufactured or hand loaded
(reloaded) ammunition or ammunition that is faulty, incorrect
or nonstandard, as both the manufacturer and the importer of
this firearm specifically disclaim responsibility for any damage
or injury whatsoever occuring in connection with or as the result
of the use of such ammunition with this firearm.
HISTORY OF THE SKS:
The concept of the assault rifle began with the Soviets in the
early 1900's. Later, during World War 1 Vladimir Federov introduced
the Federov 1916 Automatic Rifle, which fired a 6.5x50.5 SR Japanese
cartridge. At this time this cartridge was thought to be the best
for use in rapid firing rifles. These guns were used toward the end
of the 1914-18 war and the Russo-finish war of 1939-40
During world war II the russians were needed for the "Avtomat"
increased, and they adopted use of a 7.62x39mm cartridge. The weapon
created by S.G. Simonov to fire this cartridge was the SKS-45
(Samozaryadni Karabin Simonova)a self loading carbine, which was
scaled-down version of the 14.5x111.8mm PRTS anti- tank rifle. The
SKS-45 was easy to field strip and maintain and was quite popular.
At the same time, M.T. Kalashnikov was working on designing a
series of small arms, which would also use the 7.62x39mm cartridge.
He was successful, and developed one of the best known military
weapons of our time, the AK-47 (Avtomat Kalashnikova)in 1947. The
AK-47 was the prototype for many sub sequent versions, and the
chinese manufactured SKS Type 56 rifle is a direct derivative
of Kalashnikov's design.
At the conclusion of world war 2, the peoples republic of china
inherited many of these soviet weapons from the japanese. (The
Japanese had seized the in Manchuria.) During the chinese civil
war, the PRC began making this equipment, and by wars end were
well on their way to standardizing production of these soviet-
type small arms.
In recent years, the PRC has been producing the 7.62x39mm Type 68,
the 7.62x39mm Type 67, the 7.62x25mm Type 64, and the SKS Type 56
with the distinguishing folding bayonet. The SKS-56 was encountered
frequently during the vietnam war.
As a military weapon, the SKS rifle is only used by frontier forces,
however it remains ever popular with american sportsman as a hunting
weapon, and as always with collectors and firearms enthusiasts.
SPECIFICATIONS:
SKS TYPE 56
Calibre: ................................................ 7.62mm
Weight: ........................................ 8.4lbs (approx)
Length: ........................................... 40.20 inches
Barrel: ...................... 20.5 inches, 4 groove, R.H. Twist
Muzzle: ........................................... 2.410 f.p.s.
Magazine: ....................................10-round fixed box
Aiming range: ........................... .621 mile, 1 kilometer
PARTS:
The SKS rifle consists of 11 main parts.(figure1)
1. Recoil Spring Assembly
2. Reciever Cover
3. Reciever
4. Bolt
5. Gas Tube/Handgaurd Assembly
6. Bayonet
7. Stock
8. Trigger Group
9. Magazine
10. Barrel
11. Cleaning Rod
The basic SKS accessories.(figure2)
1. Cleaning Rod Head
2. Drift
3. Brush
4. Oil Can
5. Accessory Case
6. Muzzle cap
7. Gasport Cleaning Tool
8. Clip
LOADING THE SKS:
Instructions for Loading
(ALWAYS BE CONSCIOUS OF MUZZLE POSITION!!)
1. Flip the safety to the "ON" postition.
(figure3)
2. Pull charging handle on bolt carrier back until the action
locks open.
3. Load with either single rounds or stripper clips.
(figure4)
4. Again remain conscious of muzzle postition.
5. Pull charging handle back and let the bolt carrier fly forward to
chamber the first round.
6. The rifle is now loaded.
Instructions for Firing
(ALWAYS REMAIN CONSCIOUS OF MUZZLE POSTITION!!)
1. Aim rifle down range.
2. Release the safety.
3. Place the finger inside trigger gaurd on the trigger.
4. Pull the trigger.
Instruction for after firing
(ALWAYS REMAIN CONSCIOUS OF MUZZLE POSITION!!)
When the gun is fired, gas pressure is extracted from the spent
cartridges, and they are ejected. New rounds are then auto-
matically fed until all rounds are gone, or the shooter stops
firing. When finished firing, lock back the bolt and always
engage the safety before unloading unused shells.
Instructions for Unloading:
(ALWAYS REMAIN CONSCIOUS OF MUZZLE POSITION!!)
1. If bolt was locked back, rifle should be unloaded.
2. Visually inspect the magazine and chamber to confirm that
gun is empty.
3. If unsure whether empty, immediately place the safety in
the "ON" position.
4. Release the magazine cover by pulling back the magazine
cover latch.(figure5)
5. Any unexpended rounds will now be freed from the magazine.
6. Now, lock the magazine cover back in place.
7. Next, pull back the charging handle to the rear and extract
and eject the live round in the chamber. The bolt stop will
automatically lock the bolt carrier back.
(figure6)
8. Again visually inspect the weapon.
SKS DISASSEMBLY / ASSEMBLY
Intructions for Disassembly/Assembly
1. Take out all the accessories. With a finger, press in on the
cover of the accessory chamber on the butt plate and take the
case for accessories out of the stock.
(figure7)Open the case and take out the accessories.
2. To remove the cleaning rod: Swing the bayonet outward from the
muzzle of the rifle and remove the cleaning rod. Then, fold the
bayonet back down to a "march position".
3. To remove reciever cover and recoil spring assembly: Hold the
small of the stock with your left hand, pressing with your thumb
on the rear of the reciever cover
(figure8); Rotate with the right hand the reciever cover
retaining pin arm upward to its verticle position and pull the
pin out to the right as far as possible.
(figure9) Allow reciever cover to move backward 1/2"
and remove by sliding to rear.(figure10)
Remove the recoil spring from the rear of the bolt carrier.
(figure11)
(Be certain to reinstall recoil spring with C Clip end forward.)
4. To remove the bolt: Pull the bolt back as far as it will go, and
remove entire assembly.(figure12)
When reinstalling bolt, be certain magazine cover is not latched.
5. To remove Gas tube/Handguard Assembly: Use a pin punch to pry
the lever located on the right of rear sight base into the
position where the camming surface located at the front is
completely verticle.(figure13)
CAUTION: Further movement will allow operating rod and spring to escape.
6. Now remove the Gas tube/Handguard assembly, raise the handguard
assembly and rock it slowly from side to side until it can be
pulled away from the gas block.(figure14)
7. The gas piston can now be pulled out of the gas tube/Handguard
assembly.
NOTE: The seven steps listed are sufficient to field-strip the rifle
for cleaning and regular maintenance.
ASSEMBLY ONLY REQUIRES THAT YOU PERFORM THE ABOVE STEPS IN REVERSE ORDER.
CLEANING THE SKS:
Make a safe examination of the rifle to be certain it is not
loaded before cleaning. To clean, begin with the rifle field
Stripped.
Instruction for Cleaning the rifle
1. Attach the bore brush to the cleaning rod.
2. Saturate the bore brush with gun solvent and push though the
length of barrel.(figure15)
If using corrosive primer, this step is very important to
remove the corrosive residue from the barrel of your rifle.
3. Make at least 10 passes though the barrel from the muzzle end.
The cap of the accessory tube can be used to protect the crown
of the the muzzle from damage during cleaning. Use a cleaning
jag or slotted tip and push a clean dry patch through the bore.
Alternate this procedure with wet and dry patches until patches
come out clean.
4. Dry the bore with a clean patch, and then again apply a thin
coat of oil to the bore with a final oil soaked patch.
5. While cleaning the bore, you should also give the chamber area
a thorough brushing as well. Use the same technique with the
patches, alternating wet and dry until the chamber is clean. Do
not leave oil residue in the chamber.
6. Clean the bolt, bolt carrier, piston, recoil spring and reciever.
A toothbrush can be used effectively for cleaning these parts.
Wipe them dry, and then coat the bearing surfaces of the bolt
and bolt carrier with a thin coat of grease. Do not pour oil into
the reciever indiscriminately.
7. Clean the gas port block area.(figure16)
Remove the gas piston from the handguard and gas cylinder assembly,
and clean thoroughly with solvent. Remove all carbon fouling, Dry
with a clean rag, then apply a light coat of oil. (gas port cleaning
tool is normally not included in basic cleaning kits, but it is
available from SKS parts dealer.)
TO RE-ASSEMBLE REVERSE THE TAKE DOWN PROCESS
REMOVING TRIGGER MECHANISM/MAGAZINE
1. Place the safety in the "ON" position.
2. Release box magazine cover.
3. Use a pin punch to strike the trigger mechanism retaining button
at the rear of trigger bow.(figure17)
4. Once released, the trigger assembly can be pulled back from the
stock assembly.
5. With the trigger mechanism removed, and the bolt locked in the
open position, the magazine can be taken out of the stock by
simultaneously pulling the magazine down and to the rear.(figure18) When reinstalling magazine be
certain front of magazine is ingaged in lug on reciever.
AT THIS TIME, RECIEVER BARREL STOCK ASSEMBLY MAY BE REMOVED
REMOVING RECIEVER BARREL ASSEMBLY FROM STOCK
(Prior to start, remove trigger mechanism/magazine.)
1. Extend bayonet.
2. Lay gun on padded table upside down.
3. With right hand hold rear of receiver assembly tightly against
table with screwdriver or punch. With left hand, lift up firmly
on stock seperating the two pieces.
(figure19)
NOTE: Crossbolt removal is not required or recommended.
ASSEMBLY REQUIRES ONLY THAT YOU PREFORM THE ABOVE STEPS IN REVERSE ORDER
SIGHT ADJUSTMENT:
Elevation: Using a front sight elevation tool, insert the forked end of the
tool into the top of the front sight hood. Engage the tool into the flats of
the front sight post. Turn the tool counter clockwise to lower the bullets
point of impact on the target. To raise the point of impact turn the tool
clockwise.
Windage: Using a small mallet and brass punch, or an after market windage
adjustment tool, windage can be adjusted by drifting the front sight seat,
in the direction desired. From the perscective of a sight picture, move
the front sight seat in the opposite direction you want yourpoint of impact
to shift. For example, to move the group on the target to the left, drift
the front sight seat to the right.
The rear sight is an open notch type which is adjustable for elevation from
100 meters to 1000 meters(110-1100 yards). There is also an all purpose
"battle" setting on the sight ladder, set for 300 meters(330 yards). This
is attained by moving the elevation slide to the rear of the ladder as far
as it will go.
MOUNTING THE BAYONET
Begin by sliding the bayonet handle and the bayonet spring over the tang of
the spike bayonet. Push downward on the handle until the slot for attaching
the bayonet screw is exposed. Hold the bayonet carefully in this position
with the muzzle ring facing the muzzle of the rifle and insert the bayonet
pin with a screwdriver of proper size.
PARTS LEGEND
1. Piston 28. Stock assembly
2. Handguard and gas cylinder 29. Trigger guard spring
3. Piston extension 30. Magazine
4. Piston return spring 31. Magazine follower
5. Front sight 32. Follower spring
6. Front sight seat 33. Hinge pin
7. Handgurad catch 34. Magazine cover
8. Bayonet screw 35. Cover latch
9. Bayonet assembly 36. Latch spring and sear spring
10. Hold open latch pin 37. Sear
11. Hold open latch spring 38. Latch stop pin
12. Hold open latch 39. Trigger guard
13. Receiver and Barrel 40. Disconnector hinge
assembly 41. Trigger pin
14. Takedown latch 42. Safety catch
15. Trigger guard latch 43. Safety catch spring
16. Latch pin 44. Trigger
17. Rear housing 45. Safety catch pin
18. Bolt carrier 46. Trigger bar
19. Bolt 47. Trigger bar pin
20. Firing pin retainer 48. Trigger spring
21. Firing pin 49. Disconnector
22. Extractor spring 50. Rebound disconnector
23. Extractor 51. Hammer
24. Recoil spring 52. Hammer strut pin
25. Spring retainer 53. Hammer strut
26. Large spring guide 54. Hammer spring
27. Small spring guide 55. Cleaning rod
Exploded view of SKS 56